Saturday, 8 March 2014

Stone Bridge - 28MM


A relatively simple build up this time. Inspired by the foam cutting tool for my railway embankments I decided to turn my attention to a really big bridge to span my big rivers. I’d already built a wooden bridge but this would be something more permanent.

Construction started off with the base board. This would be 16cm wide and about 48 cm long – it is going to be big. Measuring out the width of the river I decided the bridge would have three arches. Apologies now but I forgot to take photos of this stage but I think from the following photos you can see how this has developed.


The design of the bridge is free style and the main element is built from three pieces of foam – a pink foam inner and two side panels of 8mm blue foam. Prior to cutting I drew out the design on the pink foam and cut out the outline of the bridge (but not the arches). The road elevation is quite steep but I wanted to give this bridge some height so a compromise on the run up was achieved. The angle is about 35 degrees. With the bridge base cut I then placed this on one of the blue sheets centred in the middle. The arches were drawn up onto the blue board along with the height of the wall.

Blue & Pink Foam

 

I then clamped all three sections together and using the foam cutter jig cut these away. You can see how I clamped these together – a bbq skewer driven through the three sections in the space where the arch will be.

The cut outs from the arches sitting on my foam cutter - you can see the bbq skewer holding pins
 

With the three pieces cut I turned my attention to the stone work that would be on show – both inside and outside of the bridge walls. I firstly drew a line following the line of the bridge about 5mm from the edge. Then using a pencil I ‘etched’ in upright stones. With this complete I then etched in the stone facing pattern – nothing to fancy a series of horizontal and vertical lines – blue foam has just the right density for this and when painted up looks the business.

 
Etched Stone work - just a pencil used

 

The bridge still looked a little fragile so to bolster the appearance of strength I cut 4 pillars from more blue foam and again etched in the stone work.
 
These pieces were all then glued together using pva and left overnight to dry.



Next up I gave the outside of the bridge its first coating of black acrylic paint. Once dry I turned my attention to the road surface. Again a coat of PVA followed by a sprinkling of sand.



 The piece was then given a final coat of black paint

 


For the river a sheet of Oxford Blue Vinyl floor tile was cut to fit the hardboard base. I lined up the bridge on top of this and cut out the edge where the bridge and river butt up together. Because the central arches will sit on the tiles I had to trim these to the height of the vinyl so everything was sitting flush.

The bridge was then fixed to the board using pva glue secured with bbq skewer pins driven up from the underside. I do this with all my terrain as it really does strengthen the overall piece.
 

 

I masked off the road sections and then covered the remaining base board with ballast right up to the river banks. This was then painted dark brown with a lighter highlight.

 

Returning to the bridge I finished off the black base coat and then processed to lighten the stone work with three successive dry brushes of lighter grey, this helps to tie it into the castle and other stone features on the table.







 

To finish off the ground cover in the form of static grass and clump foliage was added.



 
This was not a massive build and was completed in about 6 hours (ignoring drying time) – cost of materials was negligible as I had all the foam sitting around in a scrap box left over from other projects.

 Hers a couple of shots with the bridge with the river
 






Until next time

12 comments:

  1. Nice addition to the terrain stockpile!

    ReplyDelete
  2. Well you made that look ridiculously simple! Great job.

    ReplyDelete
  3. Big and impressive - a great bit of scenery.

    ReplyDelete
  4. Fantastic work! Really inspiring stuff!! I noticed Axis and allies 1914, how does it play?

    ReplyDelete
    Replies
    1. Hi there Axis & Allies 1914 best purchase of Xmas - game is great - we've played 6 times and every game has been slightly different - it is very balanced with either side capable of winning.

      Best game of the Axis & Allies stable in my opinion

      Delete
    2. Cool, I have been thinking about getting a copy myself, but wondered how close to the WW2 version (which I love) it was, thanks! Terrific bridge!

      Delete
  5. Fantastic! I might have to make a Roman bridge based on your plan. Thanks for sharing.

    ReplyDelete
  6. Good stuff, that. I need to make something similar. Appreciate the inspiration and the DIY lesson.

    ReplyDelete
  7. Great stuff. Nice to see an in scale bridge and river for once instead of the compressed version most of us go for to maximise table space.

    ReplyDelete
  8. Very nice bridge, you make it look so easy.

    ReplyDelete